Відео

Great vidoe How can i tell if the sensor needs replacing?

Awesome Video

🔥🔥🔥

Bruh my shit cut off driving doing the same shit

Thank you so much for showing all the steps! You're great :)

Okay, like that wasn't as helpful as I had hoped...

Will my crank sensor make my truck jumpy after plugs and wires are changed?

How do you take off the grease cap?

Very helpful thank you

Thank you so much. My truck had been sitting for about 6 months and I decided to get it back up and going. I noticed some corrosion on my positive terminal and sure enough it doesn’t crank and I have to jump it. I go to the store and need a jump but this time I’m idling at +2000 and I’m certain this is the problem. Thank you!

❤🎉Hello, it TRULY WORKS,I JUST DID IT TO A 97 DODGE RAM 1500,DIFFERENCE IS,MY FUSS WAS NOTTT BLOWN,IT WAS VERY,VERY DIRTY AND INSTEAD OF CLEANING IT,I REPLACED IT AND NOW ABS AND BRAKE LIGHT OFF 🎉❤🎉❤ THANKS 😊 SOOOO MUCH...❤🎉❤🎉

Thank you so much 💙💙 someone just tried to charge me $100 and I already bought the bulb .. Thank you for this video!

Mine goes out every six months it seems.

Handy man Sam, yesterday I went to start my plow pickup. Battery very weak, corrosion on both terminals. I jump started it and plowed with the idle at close to 2000 rpm. Hard on linkage and transmission. Watched your video and decided the battery needed cleaned up anyway. Wow! Running great again with idle back at 800 rpm. Must be a low battery charge sensor stepping up the idle when the battery is too corroded to take a charge. Thanks much for the video. ME

Can you do fog light bulb replacement?

Nice video. And good on you not editing out portions of the video like pulling on the tensioner for people to see how you did it.

just did this on my 1997 Saturn SL2 and may i say that bottom clip on the filter can be a pain in the ass if you don't have a good visual once i jacked up the car it took about 10 seconds to unclip. Just for someone like me who thinks they can get away with it without jacking the car up and wasting an hour trying not to break a line or something GREAT VIDEO

Thanks for the video and the helpful info! I got a 97 Ram with the 5.2 and this code popped up as well as cylinder 8 misfire. I replaced the plugs and wires. I heard somewhere that the ignition coil when it goes bad it usually comes up as a misfire.

Kinda like screwing sometimes you just have to go by feel 😂

Hell of a good video Much appreciated

Thanks dude! Hopefully this is why my engine keeps dying.

Thanks 👍👍

Did yours run rough after you installed them? I did mine and now it runs rough like somethings up with the valves...

Good Detail

I just went to a few stores - 2 automotive and 2 home improvement stores hoping to find a socket that size, shape and hole in it but found nothing that was exactly the same. So, where can I finally socket that allow me to loosen it with a screwdriver?

3258

It really sucks when you replace the crank sensor that only the after market makes out of chinesium these days and between 1-3 days later the truck starts pinging and bucking like crazy and dies again, and three crank sensors later you just decide to say screw this and convert it to 4 barrel carb and a points distributor, only using the computer for gauges because no inspection in your state and its your only solution. Im an automotive electrical guy and it boggled the crap out of my mind because I could find nothing wrong with the wiring or computer when i refused to believe I could possibly get that many crap sensors right out of the box. The 5 speed version of the truck uses a different crank sensor than the automatic and is rare and discontinued by dodge. Was running good for a couple weeks converted to carb but then the cat plugged up on me lol Eh... at least after i open it up and gut it and weld it shut again I can finally have a nice running fully restored 97 dodge pickup. It turned out nice all things considered but dude... I would have rather just been able to put a non chinesium crank sensor in it and call it done.

it fixed my truck …. Thanks ..

Great video thanks

Your instructions seem pretty straight forward but I'm stuck on step 1, I tried with all my might to pull the connector off, it wouldn't budge. I tried for half hour with no luck, it started getting dark, will try again tomorrow. I feel like being a girl I have no grip strength doing this and I don't want to break something :( This is a 2001 Solara, first time trying to replace the headlight bulbs. Any suggestions would be appreciated.

So that’s just the high beam. How do you change the low beam or regular headlight bulb?

What do you meAn let the break system breath!! That's the last thing you want in the break system AIR!. . . please don't misinformed people.

please tell me you didnt take out the tranny and exhaust to do this . hahaha i watched one where the guy took out his wheel well and tire to try and reach it but couldnt. sorry im in tears cause im as skinny as u guys and it took ten minutes sitting on the engine . so what im looking for is if anyone had to adjust or relearn the sensor after install.dodge told me it had to be adjusted , but i think he is lying cause it is a solid bracket , no adjustment bolt or spacers. idk .truck still dead.

Thanks for the help great instructions just want to add when replacing that rubber piece make sure you not covering your 3 prongs the 3 prongs have to go thru the hole it happened to me then I figured out one of my prongs was covered by the rubber piece 😨

Thanks for just showing a clean shot of the location, that's all I needed and it was easy to see it in your video!

I'll check it out hope it works

What is the name of the fuse?

Thank you for the help bro. Just bought a new pcv valve for my Saturn and gonna replace it: this video helped

Very nice. Thank you

would it flash the check engine light on the Cummins models too

hex head sockets boom

Gracias me ayudó bien mucho salí de mi problema grasias

Alright if this goes bad can it stop spark to my distributor and cause my truck to just turn over

But this basically is the tool that u use to remove this type of filter lol...

Fix or repair daily is a dodge.

very funny and informational

Really bro not good because you don't tell people the size of the fuse we see what location but you don't tell people the size of a you could have did a lot of little better thanks though I see where to go and I check my fuses I hope I can find that blue fuse I see it was blue so that's that's a start but you could have been more specific bro you just pull it out

I just had this happen about a week ago. I did what you just showed, So, how does this fix what happened? So what is going on between this low and high beam? For the headlights not working. I don't want it to happen again.

Job Well Done

Life saver thank you I was about to replace the wiring